Guided tour
Women in the museum
A guided walk through all seven halls. Thirteen displays, from braille pins to a hologram, each with at least one woman among its inventors or contributors.
Before the first stop
Welcome to the museum. This tour follows the green line on the floor. It runs through all seven halls and stops at thirteen displays. Each has at least one woman among its inventors or contributors.
The tour waits at each stop. Press the key for the next stop when you are ready. The first is the braille display in hall 1, where the picture is made of pins.
Read by touch
Refreshable braille display, hall 1
This display is read by touch. Rows of pins rise and fall to spell a line of braille. The model is spelling the time. Watch the cells on the right. They change every second.
Under each dot is a crystal that bends when a voltage reaches it, and a lever turns that small bend into the rise of a pin. Andrée Tretiakoff and Oleg Tretiakoff patented this way of raising the dots. They filed first in France, in 1974.
It is the only piece in the museum that needs no light at all. Every other stop on the green line works with light. The next is the cathode ray tube in hall 2, where a beam of electrons makes a screen glow.
A beam that draws
Look at the screen. The bright band moving down it is where one beam of electrons has just drawn its lines. The model slows it about 60 times. From the side you can see the copper coils that steer the beam.
The plate on the block names Ferdinand Braun, who built the first tube of this kind in 1897. Thirty years later, in San Francisco, Philo Farnsworth sent the first television picture made entirely by electronics. Elma Farnsworth, known as Pem, worked in his laboratories and made the technical drawings for the experiments. Her face was among the first that the system sent.
In hall 1 the picture was made of pins. Here one beam draws all of it. The next stop is the MicroLED wall in hall 3, where the picture is made of lamps.
A question at dinner
The wall in front of you is made of LEDs, each too small to see. One tile is out and leans against the stand, with the suction lifter still on it. A wall like this is repaired one square at a time.
Jingyu Lin and Hongxing Jiang are physicists. In 2000, at Kansas State University, they made the first microLEDs. They are also a married couple, and the idea began as a question at their dinner table: what would happen to an LED shrunk to thousandths of a millimetre?
Stay in hall 3. The next stop, the quantum-dot display, works with crystals far smaller than these lamps.
Colour from size
This is one pixel, cut open and greatly enlarged. Blue light rises from the lamps on the board. In the left well, large crystals turn it red. In the middle well, small ones turn it green. The right well has no crystals, and the blue passes through. The size of a crystal alone sets its colour.
The crystals are called quantum dots. Most screens use them as this model does, to turn blue light into red and green. In 1994, at Berkeley, Vicki Colvin and two colleagues took another route. They made a layer of dots glow by passing a current through it. Colvin is the first author of the paper.
The cathode ray tube, the LED wall and this pixel all make their own light. In hall 4 the sun, a lamp or a laser makes the light, and the display shapes it. Go to the shadow play, where the lamp is a flame behind a cloth.
A flame and a cloth
Look at the cloth. A flame burns behind it, and three flat figures stand between the flame and the cloth: a tree, a deer and a bird. What you see are their shadows. Watch the bird. When it flies towards the lamp, its shadow grows and its edge goes soft.
Nobody knows who first did this. It is recorded in Java and in China about a thousand years ago, and it is performed today. Holes cut through a figure let the light pass and draw an eye or a feather inside the shadow. Kara Walker, an American artist known for silhouettes cut from black paper, has made films this way since 2004. Her jointed paper puppets, worked by hand on sticks, play out stories of slavery in America.
The first stop needed no light at all. This one needs only a flame. The next stop, in this hall, draws with a beam of light. Go to the scanned laser.
Drawing with a laser
Follow the beams from left to right. Three lasers merge into one white beam. Two small mirrors on fast motors steer it, and your eye joins the moving dot into a drawing on the wall.
The plate names Joseph Ostoja-Kotkowski, who staged an early laser show in Adelaide. Elsa Garmire, a physicist at the California Institute of Technology, made laser images. They were filmed in 1972, and they became the model for Laserium, the laser show that opened at Griffith Observatory in Los Angeles.
In hall 2 a beam of electrons drew the picture inside a tube. This beam is light, and it can draw on anything: clouds, buildings, smoke. A few steps on, in the same hall, a picture is cut to fit a set of white plaster shapes.
A picture cut to fit
Find the switch marked Daylight and turn it off. By day this picture is barely visible. The projector on the tripod is an ordinary one. The work is in the picture, which is cut to fit the shapes it lands on. Each shape gets its own pattern, and no light falls on the floor.
In 1969 the Haunted Mansion at Disneyland used this for its singing busts. The faces of singers were filmed, and the film was projected onto plaster busts of the same faces. In the same house a crystal ball holds a blank head. Leota Toombs, an artist at the Disney design workshop, gave it her face: the film projected onto that head is of her.
Before you go on, turn the daylight back on. The next stop is in hall 5, where the displays behave like print: they need the light of the room. Go to the electrophoretic ink, the page of an e-reader.
A page that bends
This is the page of an e-reader. It makes no light. Millions of capsules hold black and white pigment, and a voltage pulls one colour to the top. Watch the page for a moment. Every 15 seconds it resets, with a flash of black and then of white. In between, it holds the page with no power.
The plate names Barrett Comiskey, J. D. Albert and Joseph Jacobson, who developed this ink at the MIT Media Lab in 1996. Five years later, at Bell Laboratories, John Rogers and Zhenan Bao laid it on a sheet of plastic. Bao is a chemist who designs plastics that carry a current. With a rubber stamp they printed 256 plastic transistors on the sheet, one for each dot of the picture. The page could bend.
The ink is slow, which suits a page. The next stop, in this hall, is a display of the same kind that became fast enough for video. Go to the electrowetting display.
Oil and water
Electrowetting display, hall 5
These are 12 cells, greatly enlarged. Each holds a drop of dyed oil under water. With no voltage, the oil spreads out and the cell shows its colour. With a voltage, the water pushes the oil into a corner. Watch one cell switch. The oil does not disappear. It gathers in the corner and stands higher.
At the first stop a voltage bent a crystal and lifted a pin. Here a voltage makes water push oil aside. Susan Hackwood and Gerardo Beni proposed this display at Bell Laboratories in 1981, and they gave the effect its name: electrowetting. The year on the plate, 2003, is when a laboratory in the Netherlands made it fast enough for video.
There is one more stop in this hall. Go to the electrochromic display, a printed label that shows the minutes.
Layer by layer
Electrochromic display, hall 5
This printed label shows the minutes past the hour. In this hall a voltage has moved pigment, and then oil. Here it moves atoms. It pushes charged atoms into the printed film, and the film darkens. Wait for the minute to change. The old numeral fades, and the new one darkens over several seconds. The pane of glass behind the label carries the same film.
The plate names S. K. Deb, whose work on films of tungsten oxide, in 1969, is where these displays began. At the Massachusetts Institute of Technology, Paula Hammond and Dean DeLongchamp built such films in another way: one molecular layer at a time. Their films changed colour faster, and with more contrast, than films made in other ways. The thesis that sets the work out is from 2003, and it points to a display in full colour.
That was the last display that works like print. Next is hall 6, Mid-air. Go to the illusion transmitter, where a picture hangs in the air.
A bulb that is not there
Look at the two boxes. On the left, a real bulb hangs hidden under the socket, and a curved mirror stands its picture in the empty socket above. On the right there is no bulb, only the picture, sent across by a camera and a second mirror. Watch the left bulb go dark. The picture on the right follows.
In hall 3 a question was asked at a dinner table. This one was asked at an exhibition, in 1976. Valerie Thomas saw a curved mirror make a bulb seem to glow after it had been taken out of its socket, and she asked whether the picture could be sent. When she invented the illusion transmitter, she was managing the image-processing systems for Landsat at NASA. The patent was granted to her four years after that exhibition.
Stay in hall 6 for the static-volume display, where the picture fills a block of space.
Drawing inside glass
Start with the stack of clear sheets. The figure in it is a knot. One sheet at a time turns milky and catches its slice of the picture. Nothing moves.
Now look beside the stack, at the block of glass. It glows only where two invisible beams cross, and the model draws them in red. A beam of electrons drew in hall 2, and a laser in hall 4. Here the point where two beams cross does the drawing, in three dimensions.
Elizabeth Downing and three colleagues drew coloured points of light inside glass in this way. Their work was published from Stanford University in 1996, with Downing as first author. The prototype was a cube about 15 millimetres on each side, and the model shows it many times that size. The last stop is holography, in hall 7.
The light itself
Look through the glass plate. A toy engine seems to stand behind it. Move to one side, and you see around the engine. It is not behind the glass. A hologram records the light itself. In hall 4 a laser drew the picture. Here a laser only lights the plate, and the plate sends out the same light waves that the engine did.
Dennis Gabor invented holography in 1948. Twenty years later Margaret Benyon, a painter, began to make holograms as art. A hologram like this one is static. The first holographic video display was built at the MIT Media Lab in 1989, and the thesis that Mary Lou Jepsen wrote there that year sets out its design.
The end of the green line
That is the end of the green line. It began with pins that are read by touch. It ends with a toy engine that is not there.
Fifteen women are named at these thirteen stops, and you have now stood at the work of each. In all, the labels in these halls name more than a hundred people.
The line passed more than forty other displays on the way. Leave the tour, and the halls are yours to walk. Every piece has its label, and its people are named on it. Thank you for taking the tour.
Museum of Alternative Displays / Index / People / About / Women in the museum / Black inventors and artists
English / Català / Deutsch / Esperanto / Español / Français / 日本語 / 한국어 / Português / 简体中文